Mapping Mountains – Significant Height Revisions – 100m Twmpau

Pant y Brwynog (SN 548 037) 

There has been a Significant Height Revision to a hill that is listed in the 100m Twmpau, with the summit height, bwlch height and their locations, the drop and status of the hill derived from LIDAR analysis conducted by Myrddyn Phillips. 

LIDAR image of Pant y Brwynog (SN 548 037)

The criteria for the list that this height revision applies to are:

100m Twmpau – Welsh hills at or above 100m and below 200m in height that have 30m minimum drop, with an accompanying sub list entitled the 100m Sub-Twmpau, with the criteria for this sub category being all Welsh hills at or above 100m and below 200m in height with 20m or more and below 30m of drop, with the word Twmpau being an acronym standing for thirty welsh metre prominences and upward. 

100m Twmpau by Myrddyn Phillips

The name the hill is now listed by is Pant y Brwynog and this was derived from the Tithe map, and it is adjoined to the Mynydd Sylen group of hills, which are situated in the southern part of South Wales (Region B, Sub-Region B5), and it is positioned with minor roads to its north-east, west and south, and the A476 road farther to its west, the A4138 road to its south-east and the M4 motorway farther to its east, and has the town of Pontarddulais towards the east.

When the original 100m height band of Welsh P30 hills were published on Geoff Crowder’s v-g.me website, this hill was not included in the Hills to be surveyed sub list, as it was considered not to meet the criteria then used for this sub category.

After the sub list was standardised, and interpolated heights and drop values also included the details for this hill were re-assessed and it was listed with an estimated c 27m of drop, based on the 130m summit spot height that appeared on the Ordnance Survey Vector Map Local hosted on the Geograph website and which was entitled the Interactive Coverage Map and an estimated c 103m bwlch height, based on interpolation of 5m contouring between 100m – 105m. 

Extract from the Ordnance Survey 1:25,000 Explorer map

However, it was not until LIDAR became available that the details for this hill could be accurately re-assessed.  The LIDAR (Light Detection & Ranging) technique produced highly accurate height data that is now freely available for much of England and Wales. 

LIDAR summit image of Pant y Brwynog (SN 548 037)

The height produced by LIDAR analysis to the natural summit of this hill is 127.65m positioned at SN 54886 03732, and this in relation to the spot height that appeared on the Ordnance Survey Vector Map Local hosted on the Geograph website and which was entitled the Interactive Coverage Map comes within the parameters of the Significant Height Revisions used within this page heading, these parameters are:

The term Significant Height Revisions applies to any listed hill whose interpolated height and Ordnance Survey or Harvey map summit spot height has a 2m or more discrepancy when compared to the survey result produced by the Trimble GeoXH 6000 or analysis of data produced via LIDAR, also included are hills whose summit map data is missing an uppermost ring contour when compared to the data produced by the Trimble or by LIDAR analysis.

Therefore, the new listed summit height of this hill is 127.65m and this was derived from LIDAR analysis, this is 2.35m lower than the previously listed summit height which was based on the spot height that appeared on the Ordnance Survey Vector Map Local hosted on the Geograph website and which was entitled the Interactive Coverage Map. 

ills of Wales, and are reproduced below@

The full details for the hill are:

Group:  Mynydd Sylen 

Name:  Pant y Brwynog 

OS 1:50,000 map:  159

Summit Height (New Height):  127.65m (LIDAR) 

Summit Grid Reference:  SN 54886 03732 (LIDAR) 

Bwlch Height:  102.6m (LIDAR) 

Bwlch Grid Reference:  SN 54795 03991 (LIDAR) 

Drop:  25.0m (LIDAR) 

 

Myrddyn Phillips (August 2024)