Cae (SN 560 038)
There has been a Summit Relocation to a hill that is listed in the 100m Twmpau, with the summit height, bwlch height and their locations, the drop and status of the hill derived from LIDAR analysis conducted by Myrddyn Phillips.
LIDAR image of Cae (SN 560 038) |
The criteria for the list that this summit
relocation applies to are:
100m Twmpau - Welsh hills at or above 100m and below 200m in height that have 30m
minimum drop, with an accompanying sub list entitled the 100m Sub-Twmpau, with
the criteria for this sub category being all Welsh hills at or above 100m and
below 200m in height with 20m or more and below 30m of drop. The list is authored by Myrddyn Phillips, with
the word Twmpau being an acronym standing for thirty welsh metre prominences and upward.
100m Twmpau by Myrddyn Phillips |
The hill is adjoined to the
Mynydd Sylen group of hills, which are situated in the southern part of South Wales (Region B, Sub-Region B5), and it is positioned
between the stream valleys of the Afon Morlais to its west and the Afon Gwili
to its east, and has the towns of Llanelli to the south-west and Pontarddulais
to the east.
When the original 100m height band of Welsh P30 hills were published on Geoff Crowder’s v-g.me website, this hill was included
in the main P30 list with a 119m summit height, based on the spot height that appears
at SN 56057 03826 on the contemporary Ordnance Survey 1:25,000 Explorer map.
Extract from the Ordnance Survey 1:25,000 Explorer map |
After the sub list was standardised, and
interpolated heights and drop values also included the details for this hill
were re-assessed and it was listed with an estimated c 39m of drop, based on the
118m summit spot height that appeared on the Ordnance Survey Vector Map Local
hosted on the Geograph website and which was entitled the Interactive Coverage
Map, and an estimated c 79m bwlch height, based on interpolation of 5m contouring
between 75m – 80m.
However, it was not until LIDAR became available
that the details for this hill could be accurately re-assessed. The LIDAR (Light Detection & Ranging)
technique produced highly accurate height data that is now freely available for
much of England and Wales.
LIDAR analysis gives the highest ground on this
hill as 119.9m positioned at SN 56063 03818.
However, this is to the top of a raised field boundary and protocols
dictate that as this is deemed a relatively recent man-made construct such ground
is discounted from the height of a hill.
LIDAR summit image of Cae (SN 560 038) |
The height produced by LIDAR analysis to the
natural summit of this hill is 119.0m and is positioned at SN 56069 03819, and
this comes within the
parameters of the Summit Relocations used within this page heading, these
parameters are:
The term Summit Relocations applies when the high
point of the hill is found to be positioned; in a different field, to a
different feature such as in a conifer plantation, within a different map contour, to a
different point where a number of potential summit positions are within close
proximity, when natural ground or the natural and intact summit of a hill is
confirmed compared to a higher point such as a raised field boundary or covered
reservoir that is judged to be a relatively recent man-made construct, or a
relocation of approximately 100 metres or more in distance from either the
position of a map spot height or from where the summit of the hill was
previously thought to exist.
Therefore, the height produced by LIDAR analysis
to the natural summit of this hill is 119.0m and is positioned at SN 56069 03819,
this is
relatively close to where the spot height appears, and is approximately six metres
eastward from the high point of the raised field boundary.
The full details for the hill are:
Group: Mynydd Sylen
Name: Cae
OS 1:50,000 map: 159
Summit Height: 119.0m (LIDAR)
Summit Grid Reference (New Position): SN 56069 03819 (LIDAR)
Bwlch Height: 80.0m (LIDAR)
Bwlch Grid Reference: SN 55961 04021 (LIDAR)
Drop: 39.0m (LIDAR)
Myrddyn Phillips
(December 2024)
No comments:
Post a Comment